[Silly Little Cars] 93' GO-4 REAR SHOCK

Thu Apr 3 16:35:15 PDT 2014

Just a quick response. 
Take a look at some ATV rear setups.
I would NOT start cutting and drilling just yet.
Cause no matter the length of the shock, if the swingarm has enough travel it will bottom out that shock too. 
Be aware that the springs, spring cups and other hardware are sold (most of the time) separate from the shock.
I’ll take a good long look at the pix tomorrow and get back to you.
I still think there should be a spring on that shock.
The shock in the pix have the adjustment stop on it for the spring cup to sit on.
More to come later,
Mike 

From: Bruce Moulton 
Sent: Thursday, April 03, 2014 7:12 PM
To: Silly Little Email List 
Subject: Re: [Silly Little Cars] 93' GO-4 REAR SHOCK

Mike et al, 

This is a 1993 Go-4 Model P-35 (the name "Interceptor" does not appear anywhere on the vehicle documents incl. a sales brochure.) I now have several places that seem to have a replacement for this apparently defective part that was discontinued (Shock #7041218-T3123.) But it  still begs the question what just replacing it would change since it would be completely depressed after install. Would seem more like a defective plan than a part. I have tried to send a Google Drive Doc with pictures. Images 0028 thru 0032 show the shock sitting inside the upper and lower installation brackets on the vehicle. The rest of the pix show the empty brackets from different angles plus a couple of shots of the shock. If you can't open them let me know and I'll figure another way to send. 

Please look at the bottom bracket. I have this idea that I can cut it down about 2 inches and drill a new hole lower. Then I can install a very nice heavy duty car shock that would not be compressed. Does that make sense or does anyone have a better idea? 

 IMG_0028

 IMG_0039.JPG

 IMG_0038.JPG

 IMG_0037.JPG

 IMG_0036.JPG

 IMG_0035.JPG

 IMG_0034.JPG

 IMG_0032.JPG

 IMG_0031.JPG

 IMG_0030.JPG

 IMG_0029.JPG

 IMG_0028.JPG

Bruce

brucemmoulton at gmail.com

On Thu, Apr 3, 2014 at 12:33 PM, <bugnut at windstream.net> wrote:

  Bruce, 
  What Model is your GO-4?
  Not just the year, but the model too.  Ex: P-35, BT-57, etc...
  The rear suspension setup your describing sound like that common on ATV’s or softtail Harleys.
  A single shock centered on the swing arm back to the chassis. If that’s the case then there most likely should be a spring on it to stop the shock from bottoming out (full compression).
  Pictures would help to get you the answers you need.
  Also, someone on here with the same model maybe willing to shed some light on the subject and take some pix of their setup.
  The shock could be the same, only your ride takes just one.
  I’d like to know the answer to this on too. Always wanting to learn about these things.
  Later,
  Mike

  From: Bruce Moulton 
  Sent: Thursday, April 03, 2014 1:39 PM
  To: Silly Little Email List 
  Subject: Re: [Silly Little Cars] 93' GO-4 REAR SHOCK

  Thanks for the information. Is there a way I can search this list for the mentioned email? I guess my confusion is around the springs? There is no spring anywhere around this shock and if it has been removed I don't see how it would be possible to put one on. This single shock is mounted vertically, is inside the motor housing, is attached only to the frame and motor housing, is centered on the vehicle, is not part of a pair, and seems that it can only be mounted fully compressed and thus it remains fully compressed after mounting (it was fully compressed when I removed it.) 

  That is my second confusion: Why is it always fully compressed? I keep thinking there is something wrong here but don't know what it is. Somehow I think the shocks referred to aren't the same as this shock that is not part of a pair. 

  Bruce

  brucemmoulton at gmail.com

  On Thu, Apr 3, 2014 at 5:22 AM, <bugnut at windstream.net> wrote:

    Bruce,
    I was referring to the rear also.
    There was and e-mail from a member here that explained it.
    That’s where I found out about the shocks. Found the number I ordered too ( Brand: WSM   Part # 60-321 )
    The different rated springs I found out about from local ATV repair shops. They are aftermarket for the ATV quys that want more or less stiffness in the rear for jumps or racing applications.
    Hope this helps,
    Mike

    From: Bruce Moulton 
    Sent: Thursday, April 03, 2014 2:07 AM
    To: Silly Little Email List 
    Subject: Re: [Silly Little Cars] 93' GO-4 REAR SHOCK

    Thanks for the replies. I'm not referring to the motorcycle shocks on the front wheel. This is a single small shock in the rear just behind the engine. It seems to be used to dampen the the engine movement some from the frame. In order to install inside the present clamps it must be completely compressed then bolted in the compressed state. I can't make sense out of why this would be be but I can't get a replacement shock as it is discontinued and nothing else fits in the clamps. Even if I could it just seems wrong to me. Why would a shock be mounted compressed? 

    Bruce
    brucemmoulton at gmail.com

    On Wed, Apr 2, 2014 at 4:13 PM, <bugnut at windstream.net> wrote:

      Bruce,
      Does the 93 have springs over the shocks?
      I know my 96 does.
      The replacement shock for it, I believe, is the same as a Polaris Sportsman 400L.
      I think the springs are available in different stiffness and are the same as the Polaris also.
      Of course 2 are required for the Go-4’s. Oh, the shocks are adjustable too.
      My 96 is leaning to the right, so I’m going to replace both, springs maybe.
      Hope this helps,
      Mike 

      From: Bruce Moulton 
      Sent: Wednesday, April 02, 2014 7:05 PM
      To: silly_little_cars at lists.sillylittlecars.com 
      Subject: [Silly Little Cars] 93' GO-4 REAR SHOCK

      I noticed the rear shock in the engine compartment on my 93' was fully compressed so I took it out to replace. Of course it is not made anymore but in trying to figure it out the shock itself seems fine but is fully compressed when on the vehicle no matter if it were new or not! It would seem like it would not work or do anything if installed in compressed state. Does anybody know why? What would happen if I cut the bottom clamp down a bit, drilled a new hole, and installed a different shock than the original that was not compressed after install?

      Bruce1804
      brucemmoulton at gmail.com

--------------------------------------------------------------------------

      _______________________________________________
      Silly Little Cars Email List
      sillylittlecars at sillylittlecars.com
      http://lists.sillylittlecars.com/listinfo.cgi/silly_little_cars-sillylittlecars.com
      To unsubscribe, click that link above.

--------------------------------------------------------------------------
              This email is free from viruses and malware because avast! Antivirus protection is active. 

      _______________________________________________
      Silly Little Cars Email List
      sillylittlecars at sillylittlecars.com
      http://lists.sillylittlecars.com/listinfo.cgi/silly_little_cars-sillylittlecars.com
      To unsubscribe, click that link above.

----------------------------------------------------------------------------
    _______________________________________________
    Silly Little Cars Email List
    sillylittlecars at sillylittlecars.com
    http://lists.sillylittlecars.com/listinfo.cgi/silly_little_cars-sillylittlecars.com
    To unsubscribe, click that link above.

----------------------------------------------------------------------------
            This email is free from viruses and malware because avast! Antivirus protection is active. 

    _______________________________________________
    Silly Little Cars Email List
    sillylittlecars at sillylittlecars.com
    http://lists.sillylittlecars.com/listinfo.cgi/silly_little_cars-sillylittlecars.com
    To unsubscribe, click that link above.

------------------------------------------------------------------------------
  _______________________________________________
  Silly Little Cars Email List
  sillylittlecars at sillylittlecars.com
  http://lists.sillylittlecars.com/listinfo.cgi/silly_little_cars-sillylittlecars.com
  To unsubscribe, click that link above.

------------------------------------------------------------------------------
          This email is free from viruses and malware because avast! Antivirus protection is active. 

  _______________________________________________
  Silly Little Cars Email List
  sillylittlecars at sillylittlecars.com
  http://lists.sillylittlecars.com/listinfo.cgi/silly_little_cars-sillylittlecars.com
  To unsubscribe, click that link above.

--------------------------------------------------------------------------------
_______________________________________________
Silly Little Cars Email List
sillylittlecars at sillylittlecars.com
http://lists.sillylittlecars.com/listinfo.cgi/silly_little_cars-sillylittlecars.com
To unsubscribe, click that link above.

---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sillylittlecars.com/pipermail/silly_little_cars-sillylittlecars.com/attachments/20140403/7211b28a/attachment-0004.htm>